Default Password, Login and IP for your LG-Nortel ELO WR300N (LNWR300N) router. User Manuals and How to Factory Reset your LG-Nortel ELO WR300N (LNWR300N) router. LG-Nortel router default Login, IP and Passwords. To perform a LG-Nortel router Login or Reset, follow these instructions. Router manuals are also included.
Regarding third party firmware support, on the openwrt-devel ML (w/ ) + Ubicom's (since pulled) previous source code release to OpenWrt may be of interest. As an U-MEDIA device (dated ) This device is presumed to be a U-MEDIA WRT-383U based on the appearance and specs. It is also quite similar in appearance to the ( U-MEDIA WRT-372U), but the WRT-383U also appears to be used for a later revision TEW-631BRP. The WRT-383U is shown with colored Ethernet jacks (blue for WAN, yellow for LAN). While the WRT-372U is shown with black Ethernet jacks.
The WRT-383U is also shown as using a 12V 1A power adapter versus the WRT-372U's 5V 2.5A adapter.
Contents • • • • Serial [ ] Pinout [ ] The pinout used is common to Arcadyan units. ^ to back of the unit, power section J1 [ ] ( ) ( ) ( ) (3.3) ( ) (RxD) (TxD) ( ) (GND) General [ ] After booting, Shift-0 will allow access to debug mode. Option 4 would appear to allow fetching + flashing of firmware via TFTP, to some extent. Info derived from [ ] boot log ar531xPlus rev 0x00000087 boot loader startup.
Flash initialized SDRAM initialized Cache initialized Copy program from 0xbfc00000 to 0x80520000, length 0x0000cd04 bytes. Done Jump to SDRAM 0x80520cb4 [0x10000008, 0x00000000, 0x00000000] Clear BSS section. Done Stack: 0x8053eb20 Heap: 0x8053eb30 ============================================================================ Wireless Gateway WG4005E 1-LF-17 LN Loader V2.00 build Nov 14 2007 18:17:34 Arcadyan Technology Corporation ============================================================================ Copying boot params.DONE cpuFreq=240000000 sysFreq=60000000 cntFreq=120000000 Press any key to enter command mode. Checking Valid Image in Flash. Unzipping program from bank 2....done *** WEB image writing into the 16MB SDRAM has completed *** Try to find image for running. Valid Code found in the Flash...................................done Uncompressed size = 2161965 I am going to run the Code image from 80001000 firmware startup. Stack: 0x80c83150 Heap: 0x80c83160 D:/MyProjects/ttf2004/source/firmware/project/smc/wg4005e1-lf-17-ln/ar5315/gpio.c: feed_watchdog is called??
D:/MyProjects/ttf2004/source/firmware/project/smc/wg4005e1-lf-17-ln/ar5315/gpio.c: setGpio is called?? ##### _ftext = 0x80001000 ##### _fdata = 0x801D1C50 ##### __bss_start = 0x80210D2D ##### end = 0x80C7315C ##### Backup Data from 0x801D1C50 to 0x80C9315C length=0003F0DD [CGI] Web SDRAM area is from 0X80E00000H install_exception Installing TLB Refill exception handler from 8000ED00 to 80000000, size=184 Installing General exception handler from 8000EDB8 to 80000180, size=216 Installing Interrupt exception handler from 8000EE90 to 80000200, size=160 misc_int_init mips_int_enable: 0x00000400 Connect the AHB interrupt sysBoardDataInit Init the GPIOs!!! Enable arbitration for SOC devices!!! CpuFreq=184000000 sysFreq=40000000 cntFreq=92000000 AR531X_TIMER=00061A6D AR531X_RELOAD=00061A80 AR531X_IMR=00000028 mips_cp0_status=10000401 mips_cp0_cause=30800000 [INIT] MTinitialize. Runtime code version: V2.09 System startup. [INIT] MTmeminit. [INIT] check COLOR 0.
[INIT] soho initialize COLOR1: 819200 [INIT] soho initialize COLOR2: 524288 D:/MyProjects/ttf2004/source/firmware/project/smc/wg4005e1-lf-17-ln/ar5315/gpio.c: feed_watchdog is called?? It is 2MB Flash. Set flash memory layout to Runcode version: V2.09 Runcode date: Jan 4 2008 13:53:32 Bootcode version: V2. Hrm Ccsa X64fre En-gb Dv5.iso. 00 Serial number: J818033937 Hardware version: 01 sizeof(struct III_Config_t) is 125688!!! Invalid wireless channel range 0 ~ 0!!! Use default value 1 ~ 13 default route: 0.0.0.0 BufferInit: BUF_HDR_SZ=48 BUF_ALIGN_SZ=8 BUFFER_OFFSET=112 BUF_BUFSZ0=384 BUF_BUFSZ1=3264 NUM_OF_B0=200 NUM_OF_B1=1000 BUF_POOL0_SZ=86400 BUF_POOL1_SZ=3312000 sizeof(BUFFER0)=432,sizeof(BUFFER1)=3312 *BUF0=0x808eae34 *BUF1=0x805c24a4 Altgn *BUF0=0x808eae40 *BUF1=0x805c24b0 End at BUF0:0x808fffc0, BUF1:0x808eae30 buffer0 pointer init OK!
Buffer1 pointer init OK! Time =, 00:00:00 TRAP(linkUp): send ok! Interface 0 ip = 127.0.0. Sony Dsc W220 Driver For Windows 7. 1 ar531xmac_init: ifno=1, initstr=UNIT=0 VLAN=1 D:/MyProjects/ttf2004/source/firmware/hardware/ar5312/ar531xbsp.c:sysEnetInit is called ae531xEndLoad: loading device.